![]() ![]() Add ETH ALPH dual mining mode for LHR cards (ETH 68% / ALPH 32% by default).Add ETH ALPH dual mining support for non-LHR cards.Miner uses incorrect worker name for the secondary algorithm if -worker2 is set.-lhr-algo parameter is deprecated and is now an alias for -dual-algo.In order for the miner to re-tune your cards, remove LHR tune values from your config if you previously set them.Improve ETH ALPH dual mining performance for LHR cards (high power limit / core clock is important to get high ALPH hashrate).Also, DONT specify -lhr-tune or -lhr-autotune-mode, and let the miner pick the tuning values on its own. The unlocker will not work with older drivers. If you experience regular LHR locks with T-Rex 0.25.12 from releases, please give this build a go. Slightly modified the way LHR unlocker works and hopefully made it more stable.(ethash, blake3) Fixed “Duplicate share” issue.LHR unlocker is more stable compared to 0.25.12, infinite LHR lock loops should be solved now.lhr-low-power 0,1,1,0 - the second and third GPUs will be working in low power mode.If you previously had -lhr-low-power in your config, the equivalent would be -lhr-low-power 1 (LHR) Low power mode can now be set for GPUs individually, e.g.(LHR) Change -lhr-autotune-step-size default value to 0.1 (previously 0.5).lhr-autotune-interval 5:120, meaning that in -lhr-autotune-mode full mode the miner will be increasing LHR tune value every 5 minutes, and decreasing it as soon as it starts tripping LHR more frequently than once every two hours. (LHR) Allow setting “up” and “down” auto-tune intervals separately, e.g.LHR tune values aren’t accurate, but once you’ve found a value that’s stable for your GPU, you can set it manually with -lhr-tune and get consistent results across miner restarts. (LHR) Extend the new LHR unlock functionality to ETH ALPH dual mining, and ERGO single mode.Then you enter > when you are prompted on the web interface. That will generate a Key, that you can pasted into your -api-key config file entry. To solve this error, you have to use the command line: It can also be a problem of overclocking the video card. Setting Windows virtual memory to 21000 MB should resolve this “GPU idle” error. lhr-low-power - Reduces power consumption in LHR mode at a cost of a slightly lower hashrate. lhr-autotune-interval LHR auto -tune time interval in minutes ( default: 20 ).Īmount of time the GPU must be mining without hitting LHR locks before the miner increases LHR tune value.Īlso, if the GPU has triggered an LHR lock, LHR tune value will not decrease if the previous LHR lock was detected more than -lhr-autotune-interval minutes ago. Indicates by how much LHR tune value is changed by the LHR auto -tuner. LHR tune value is fixed during mining, and will not change no matter how often LHR lock is detected down - LHR tune value will decrease if the miner detects LHR lock full - same as "down" but additionally miner will be trying to increase LHR tune value if its stable on the current LHR tune level -lhr-autotune-step-size LHR auto -tune step size ( default: 0.5 ). ![]() lhr-autotune-mode LHR auto -tune mode ( default: full ). lhr-algo - Specify the second algorithm to use in LHR unlock dual mining mode. Enter -lhr-tune 68 or any other supported value in the text box.Select the device to which you want to apply LHR unlock.Open bat file (or command line in HiveOs).mt 3,3,3,0 (applies tweak mode #3 to all cards except the last one). mt 4 (applies tweak mode #4 to all cards that support this functionality). Can be set to a comma separated list to apply different values to different cards. Requires running the miner with administrative privileges. Supported on Pascal GPUs with GDDR5 or GDDR5X memory only. The effect is similar to that of ETHlargementPill. General recommendation is to start with 1, and then increase only if the GPU is stable. log-path c:\trex.log or wherever you want it really depend where you want it to be save you can create a folder then type in the full location. l, -log-path - Full path of the log file. To start saving logs for T-Rex, add the parameter -log-path trex.txt to your mining configuration. Use the file config_example as a starting point to create your own configuration. To launch T-Rex from the config.txt configuration file, enter in the console: t-rex -c config.txt c, -config \ - Use config in JSON format instead of batch file (CMD file). h, -help - display help information and exit ![]() ![]() You do not need to use this and that together.įurther commands will be separated by commas. Important! Use either a long synonym -algo or a short one -a. algo or a short synonym for this command -a - Selects the mining algorithm. ![]()
0 Comments
Leave a Reply. |